#HOW TO MAKE YOUR OWN BACKDROPS FOR PHOTOGRAPHY HOW TO#If you want to add a special effect, continue reading and learn how to make a distressed wood effect. If you are content with it you can stop here. At this point, you should already have a pretty decent wooden backdrop. Make sure to move along the grain of the wood. Just dab the sponge in the stain and start running it across the boards. To avoid dripping I recommend using a sponge or a cloth instead of a brush. I diluted it at a ratio of 1:8 with turpentine so that it will dry faster.Īfter having your stain prepared you can start staining the wood. I chose to work with concentrated bitumen stain. A good alternative is brewing strong black coffee (no sugar) and use it as a water-based stain. If you want to work with baby photo sessions, don’t use bitumen or turpentine because they can be toxic. If you are working on a limited budget, concentrated stains are a good choice. Concentrated stains are more affordable, and you can choose (to a certain degree) how much to dilute it and with what. The good thing about the diluted ones is that you can start using it immediately. You can find diluted stains as well as concentrated stains such as bitumen or turpentine at your local hardware shop. Step Four: Staining the Wood Choose a Stain for Your Backdrop You should keep in mind the total thickness of wood you have and choose the length of the screws accordingly.Īt this point, you should leave the plates overnight for the glue to set and dry. I made sure to use screws that will be long enough to go through the beam and be buried in the boards without penetrating to the front. Then drive screws to connect between each of the boards and the beams. You want to place the pilot holes ten centimeters apart from each other so that each board in your plate has a hole. First, you need to flip the plate so that it faces down.īefore starting, I marked and drilled pilot holes into the beams to make it easier to drive the screws in and help avoid splintering. The next step is to connect two beams to the backside of the plate with wood screws. You should look at the boards and decide that before attaching them together. What side of each board do you want to be facing forward? Something you should think about at this step. If your boards don’t have grooves just glue the boards together pressing them side to side. When you interlock them, they will stick together.įit the boards into each other’s grooves so that you get a plate made of 7 planks. Inject carpenters glue into the grooves of the flooring boards. They will weaken the wood and you really don’t want to let them into your home. Be careful of nails and screws, you don’t want to get cut by a rusty nail.Īlso, pay attention and make sure they don’t have any signs of termites, mold or fungus. You can use wood you have at home or you can try and find some. I want to note that you do not have to buy boards. The important thing you need to keep in mind is that they need to be thick enough so that the screws you’ll use in the coming steps will be buried in them. For this size, I used two 60cm long 3.8cm by 1.8cm beams. I made the platforms one meter wide by 70 centimeters long and used 7 boards for each platform. One could be used as a standing background and one as a flooring background (for photos from above). Choose the Right Beams to Hold Your Boards Togetherīesides the flooring boards, I used pine wood beams to attach the boards in order to make the platform more rigid. And they are made to interlock with one another so it is easier to organize them. These are affordable and they come already packed. You can buy shorter boards or ask at the shop to cut them for you. I bought 2 meter longboards which I later sawed in half. I prefer flooring boards because they come at the right width, thickness and length. Once the backdrop is finished it will be easy to move around. You can either leave it as is and have a nice light wood background or add a bit of wood stain to create a barn wood background. I chose to use pine because this wood is light-colored and easy to work with. Why I Used Pine Flooring Boards to Build My Wood Backdrop Get the materials that you feel will answer your needs. Keep in mind we are talking about the background of your image. Do you want it to have a new and luxurious look or do you want it to look old and vintage? Think of the look you want your backdrop to have. For the standalone backdrop version: Small hinges with matching, an electric sander, and a power drill.Wood stain (I used bitumen\asphalt pigment stain, but you can use any stain you want).Sanding paper (grit size 120 should be enough).7 pinewood flooring boards (10cm x 100cm x 0.9cm). #HOW TO MAKE YOUR OWN BACKDROPS FOR PHOTOGRAPHY FREE#Feel free to adjust and improvise according to your needs and resources. I used what I had available and fit my needs. What You Need to Make Your Own DIY Backdrop
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |